隔热断桥铝型材穿条机一台价格，开齿穿条一体机报价

隔热断桥铝型材穿条机一台多少钱，开齿穿条一体机报价，二步法穿条设备厂家直销诺托数控诺托穿条机联系国内销售部刘经理 微信同手机号  


齿是通过安装在开齿机上的硬质滚齿轮在铝型材用于穿条的槽口颈部滚出齿来，是特别关键的一道工序。滚齿轮通过传输机构由电机驱动而产生转动，滚齿轮外缘的60度形状的齿压在铝材槽口*并施加一定压力，带动铝材向前移动，同时在压过的槽口外沿滚出齿来。滚齿轮通过导轨能上下左右调节，以适应不同高度和宽度的型材 
Hobbing is by installing in hard rolling gear hobbing machine in the aluminum used to slit neck wear of the roll out teeth, is a process with the special key. Roller gear and driven by a motor through a transmission mechanism, 60 degrees shape of the outside of the roller gear tooth pressure in the middle of the aluminum slot and a certain pressure, led aluminum moving forward, at the same time outside the pressure of rabbet along the tooth to get out of. Rolling gear through the guide to the up and down or so control, in order to adapt to different height and width of the profile 
Open tooth wear all-in-one 
齿应开在槽口的外锤头侧，在内锤头尽可能不开齿或只开很浅的一点齿。原因是在后面的滚压工序中，外锤头会产生以自己颈根部为圆心的旋转变形而将开好的齿压入隔热条，从而保证滚压后隔热铝材的剪切强度。而槽口的内侧为定位部位，用来保证滚压后隔热型材的整体形状尺寸，就算内侧的齿开的很好，滚压后也压不到隔热条里，因此没有任何效果 
Teeth should be open on the hammer head outside the side of the slot, hammer head, as far as possible, don't open or open only shallow tooth. Reason is that in the back of the rolling process, the hammer head will produce deformation of the rotation of the centered on his neck roots and will have a good tooth pressure into the insulation, so as to ensure the shear strength of insulating aluminum after rolling. And the inner side of the slot for locating part, which is used to ensure the overall shape of insulating material after rolling size, even if the inside of the gear drive is very good, also after rolling pressure is less than heat insulation in the article, so there is no any effect 
好齿形的齿峰应小于0.2mm,不**过齿距的三分之一左右，这样滚压时才容易压入隔热条内。如果开齿太钝或没有开齿，就难以压入隔热条，隔热型材的剪切性能就无法保证。开齿的好坏主要由开齿轮质量、机器设备稳定性和操作水平来决定的。 
Good tooth shape of the teeth should be less than 0.2 mm, less than a third of the pitch, so when rolling pressure easily into the insulation within the article. If the tooth is too dull or no teeth, it will be difficult to press into the heat insulation, heat insulation material shear performance will not be able to guarantee. The stand or fall of hobbing is mainly composed of drive gear, machinery and equipment, quality stability and operation level. 
开齿轮外缘的齿形斜面应左右不对称，外侧角度应大些，这样方便将齿开在铝材槽口外侧。开齿穿条一体机开齿轮是损耗件，时间一长外缘的齿就会逐渐磨损，一般建议120吨左右要换新的开齿轮，当然这要看开齿盘的材质，差一些的几十吨就要更换，好一些的进口轮能使用更长的时间。开齿穿条一体机好的设备因稳定性好，往往更容易保证开齿的质量，若设备的稳定性欠佳，就会造成开齿盘的跳动，使得同一支型材一段开齿好，一段开齿不好，影响整体的开齿质量